Frequently asked questions about pleated blinds without drilling

Yes. The adhesive profiles are placed on the glass, so there is no drilling into the aluminium. Do check that there is enough clearance around the window handle, seals and glazing beads. With narrow or unusual aluminium profiles, it is best to send photos for advice.

Yes. uPVC window frames and tilt-and-turn windows are an important application. The window frame stays intact because the system is attached to the glass. View fabrics and colours →

Yes, as long as the glass surface, the seals and the available installation space are suitable. The fixing is on the glass and not with screws in the wood.

Yes. In addition to the standard installation on the glass, Stick & Fit can be installed on the window frame, provided the surface is sufficiently wide, smooth, flat and grease-free. In that case, measure and order the total desired width and height on the window frame. Check beforehand that the window handle and all moving parts remain clear.

Yes, in a suitable situation the tensioned product moves with the window. Check beforehand that the operating rail, adhesive profiles and corner feet do not touch the window frame, the handle or an adjacent part of the window anywhere.

Yes. The system can be placed on a fixed glass pane. Here too, each glass pane is measured separately and fitted with one product.

That is possible if the product fits within the individual glass pane and there is enough space to open and close the door fully. Also check the position of the door handle.

Only if the sliding door is deep enough and the fitted profiles and operating rails do not touch the sliding parts. For a sliding door, always send overview and detail photos for a technical check.

The height is usually measured from the underside of the vent to the bottom of the glass pane. See the separate drawing on the measuring page. The exact space around the vent remains decisive.

That depends on the window. Stick & Fit is a rectangular product and cannot be opened and closed at an angle or diagonally. On a rectangular roof window, such as certain Velux windows, the system can be used if the situation is technically suitable and the width is no more than approximately 80–90 cm. Always send photos and measurements for this so they can be checked.

Yes, precisely because there is no drilling. Bear in mind that adhesive profiles must be removed carefully and that any adhesive residue must be cleaned off the glass calmly. If in doubt, also check the agreements with your landlord.

Measure in millimetres, at several points and at least twice. Write down each measurement straight away and use the smallest measured width and height. Measure each glass pane separately.

Before ordering, look at the complete measuring instructions with drawings.

No. Give the measured size as the measuring instructions prescribe. Do not deduct millimetres on your own initiative, because the production size is based on it. View the measuring instructions →

That depends on the shape and thickness of the seal. With a thin, flat seal the installation position may be different from that with a thick or rounded seal. The measuring page shows the different situations. If in doubt, send a clear detail photo.

Glass panes and window frames can deviate by a few millimetres. By checking left, right, top and bottom, you prevent a product from being too large at one point.

The width is between 230 and 1800 mm. The height is between 200 and 3000 mm. A combination within these limits must also be technically suitable for the window.

No. Stick & Fit is made per individual glass pane. For a window with two or more panes, you measure and order each glass pane separately.

Yes. Send one overview photo taken straight in front of the window and detail photos of the edge of the glass, seals, handle and any trickle vent via the contact page.

Stick & Fit is produced according to your measurements and choices. As a result, no regular right of withdrawal applies to a correctly delivered made-to-measure product. In the event of an error, defect or deviation from the order, your statutory rights of course remain. Read the terms and conditions.

You do not need a drill, screws or wall plugs. A good spirit level, ruler and pencil help with aligning straight. Use the degreasing wipe supplied and follow the installation video and the installation guide.

Yes. The adhesive profiles are very strong and resistant to heat and cold. For long-lasting adhesion, the glass must be completely clean, grease-free and dry. Do not touch the adhesive layer, align the profile straight and press it firmly along its entire length.

Install at a temperature between 15 °C and 35 °C. If the glass is too cold or too warm, adhesion may become less reliable.

First let the adhesive strips bond fully and do not use the product for the first 24 hours.

The installation is designed to be carried out quickly, but work without rushing. Cleaning properly, checking left and right and aligning straight are more important than speed.

Small air pockets may occur and normally do not affect operation, as long as the profile has been pressed evenly and firmly everywhere.

Yes. First detach the pleated blind and the clips according to the removal instructions. Then pull the adhesive strips off slowly and evenly. Any adhesive residue can be removed from the glass with a non-abrasive product.

The installation page has the instruction video; the complete installation guide is on a separate page, with all installation and removal steps.

There are three main groups: Single Tone with 15 colours, Duo Tone with 6 colours and a white reverse side, and Black-out with 13 blackout colours. With Black-out, both visible sides have the same colour; the metallised blackout layer is inside the honeycomb. View fabrics and colours →

The Black-out fabric is 100% blackout. With sloping window frames, thick seals or small gaps at the edges, a little light may come in along the sides; the complete product then gives approximately 98% blackout.

Yes. With top-down/bottom-up you can screen the middle or lower part of the window, while daylight comes in at the top.

Stick & Fit always has top-down/bottom-up. This means you can also position the same version as top-down only, bottom-up only, a middle band or fully closed. These are positions of one system, not separate product versions.

The air chambers in honeycomb fabric can improve comfort near the window and limit heat transfer. It remains a window covering and does not replace structural insulation or external sun protection. View fabrics and colours →

That is possible in many situations. Choose a suitable fabric, ventilate the room well and avoid direct contact with water, condensation drops, grease and aggressive cleaning agents.

RAL 7016 anthracite grey, RAL 7035 light grey, RAL 9005 black, RAL 9001 cream and RAL 9003 white. The adhesive profile and operating rail may have different colours. View fabrics and colours →

Yes. Request free fabric samples so that you can assess colour, texture and light transmission at your own window and in your own interior. View fabrics and colours →

The operating rail has a handle-free, slightly hollow shape. You grip the rail with your fingers and slide it gently up or down. For tall windows you can order a control wand as an extra.

Check that the cords run straight and without twisting through the side profiles, that the clips are fully clicked into place and that both side profiles have been installed straight. Do not force the operation.

Clean the fabric carefully with a soft brush or cloth and do not press too hard. You can treat stains carefully with a slightly damp cloth. Then let the fabric dry well in the fully closed, unfolded position. Do not use aggressive cleaning agents.

Use a soft, slightly damp cloth and dry the profiles afterwards. Avoid abrasive sponges, solvents and lots of water near the adhesive strips.

Always keep cords out of the reach of children, prevent loops or tangling and do not place beds, cots or furniture directly next to the cords. Install and use the product only in accordance with the guide.

Send a photo of the complete window and a detail photo of the problem, together with your measurements and the order number if available. Use the contact form, call 085-2736378 or email info@plissezonderboren.nl.

Yes. PlisseZonderBoren.nl is part of BlindDesign, a specialist in made-to-measure window coverings.