Clean the glass
Make the entire bonding surface grease-free with the degreasing wipe supplied and let the glass dry completely.
Installation without drilling
Fitting a Stick & Fit pleated blind on the glass
With calm preparation, you fit Stick & Fit in about 5 minutes, without a drill or screws. Watch the installation video first and work accurately. A completely grease-free and dry glass surface and the correct left/right orientation are decisive; after hanging, let the adhesive strips bond fully for 24 hours.
Without drillingNo screws in the window frame
15–35 °CSuitable installation temperature
About 5 minutesActive installation time
24 hours' restLet the adhesive strips bond
Watch before you start
The complete installation video in 2 minutes and 53 seconds
The video shows the installation in 23 steps. Watch it all the way through first and, if you like, play it again while fitting or pause at each step.
Good preparation
Take your time to clean, check and align
The installation itself is simple, but careful preparation prevents crooked profiles and poor adhesion.
Check the temperature
Only install when the surroundings and the glass are between 15 °C and 35 °C.
Determine left and right
Always check L and R as seen from inside the window. The correct orientation is needed for proper operation.
Align straight
Use a spirit level, ruler and pencil for aligning. A drill or screwdriver is not needed.
Read and keep
The complete Stick & Fit installation guide
The guide contains the full installation, the important warnings, the instructions for the tensioned cords and a separate chapter on removal.
What the guide covers
- Safety and preparationThe tensioned operating cords and children, the installation temperature of 15 to 35 °C and the tools you need.
- Installation in 21 stepsFrom degreasing the glass and the L and R markings to clicking the profile into place at the bottom.
- The first 24 hoursWhy you should not operate the pleated blind yet and why small air pockets under the adhesive strip are normal.
- Removal in 12 stepsMoving house or relocating: taking the side guides off the glass without damage.
Important after installation
Give the adhesive strips 24 hours to bond fully
Do not operate the pleated blind immediately after installation. The first day is important for strong and even adhesion.
Leave the product alone after installation. This gives the adhesive strip time to bond fully.
Small air bubbles under the adhesive strip may occur and, according to the guide, do not affect operation.
Always keep cords out of the reach of children and prevent cords from becoming tangled or forming loops.
Avoid having to put things right
Common installation mistakes
A few extra minutes of checking before pressing into place prevents most problems.
Not degreasing completely
Dirt, dust or grease reduces adhesion. Clean the entire bonding surface and let it dry properly.
Mixing up L and R
Check the markings as seen from inside the window before you click parts into place.
Removing the film in one go
Work gradually from top to bottom. This keeps the profile straight and under control.
Touching the adhesive layer
Fingerprints on the adhesive layer can reduce adhesion. Only hold the film and the profile.
Not pressing firmly everywhere
Press the side guide evenly and uniformly against the glass along its entire length.
Operating too soon
Wait 24 hours after installation before using the pleated blind.
Frequently asked questions
Practical questions about installing Stick & Fit
Do I need tools for the installation?
You do not need to drill or screw. A spirit level, ruler and pencil are useful for careful alignment. Also use the degreasing wipe supplied.
At what temperature can I install the adhesive profiles?
The guide recommends installing at a temperature between 15 °C and 35 °C.
How long should I wait before operating the pleated blind?
Do not use the blind for the first 24 hours. During that period the adhesive strip can bond fully.
How do I know which profile goes on the left and which on the right?
Check the L and R markings as seen from inside the window. The correct orientation is important for operation.
Are small air bubbles under the adhesive strip a problem?
According to the installation guide, small air pockets are normal and do not affect operation.
Can Stick & Fit be removed again later?
Yes. The guide contains a separate step-by-step plan for removal in 12 steps, with which you carefully take the adhesive profiles off the glass.
Need help?
Unsure while installing?
Stop before you press the adhesive profiles firmly into place and get in touch. With a clear photo of the window and the parts, we can take a targeted look with you.
